Gas Adsorption Separation

เครื่องมือกลุ่ม Gas Adsorption and Separation จาก AMI ออกแบบมาเพื่อการวิเคราะห์พื้นที่ผิว, ขนาดรูพรุน และสมบัติการดูดซับของวัสดุทั้งแบบ mesoporous และ microporous อย่างครบวงจร ด้วยระบบแบบหลายสถานี (Multi-station) และการควบคุมสุญญากาศขั้นสูง เครื่องมือของ AMI ให้ความแม่นยำ ยืดหยุ่น และสามารถรองรับการทดสอบได้พร้อมกันหลายตัวอย่าง เหมาะทั้งสำหรับงานวิจัยและการควบคุมคุณภาพในอุตสาหกรรม ครอบคลุมตั้งแต่การวิเคราะห์การดูดซับแรงดันสูง ไปจนถึงการวิเคราะห์ BET แบบไดนามิกและการดูดซับไอระเหยอย่างละเอียด

Matrix 1000 Series

Modular Multi-Station Surface Area & Pore Analysis System

Configure mesopore, micropore, or mixed-mode stations in a single unit to match experimental needs
Surface area can be measured down to 0.05 m²/g (mesopore) and 0.0005 m²/g (micropore), Pore size ranges from 0.35 to 500 nm
Run simultaneous, independent analyses without cross-interference
Expand modularly to a total of up to 3 connected units (12 stations) for maximum throughput and flexibility
Harsh Chemistry Option: Equipped with a passivation coating and seals upgraded to FFKM for aggressive or corrosive chemistries.
Built-in, high-temperature degassing furnace with programmable ramp/soak control and real-time pressure feedback

AMI-Sync Series

Synchronous, High-Throughput BET & Mesoporous Analysis

Synchronous multi-port design enables simultaneous BET and porosity measurements across 1, 2, 4, 8, or 12 analysis stations.
Perform 4 BET measurements in approximately 20-30 minutes under fully optimized conditions.
BET repeatability of ≤ +1.0% ensures high accuracy and reproducibility.
Flexible configuration with optional degassers, multi-channel gas inlets, and thermostatic water baths for full system integration.

RuboSORP MPA Series

Automated High-Pressure Gas Sorption Analysis Precise, Flexible, Scalable

Fully automated system for characterizing gas sorption under high-pressure conditions.
Wide pressure range: vacuum to 200 bar.
Broad temperature control: –196°C (optional LN₂ cooling) to 500°C; custom configurations available.
Configurable with 1, 2, or 3 independent analysis stations.
Optional BET surface area analysis capability for added versatility.
Up to 2 additional volume-configurable chambers for optimized kinetic measurements
Supports multiple test modes: PCT (Pressure–Composition–Temperature), dynamic adsorption, and both PCT/dynamic cycling tests.

BTsorb 100 Series

Breakthrough Curve and Mass Transfer Analyzer

Performs breakthrough curve testing and multi-component competitive adsorption.
Optional analysis of mass transfer performance, including diffusion coefficients via chromatography and ZLC methods.
Supports PSA, TSA, and liquid-phase sorption experiments.
Stable, constant-temperature system for reproducible results.
Operates up to 100 bar for high-pressure gas separations.
Optional configurations include vapor handling, integrated mass spectrometry, and sulfur-resistant corrosion protection.

Meso 112/222

Optimized for Mesoporous Characterization and Independent Station Control

Designed for precise specific surface area and mesoporous structure characterization.
Available with 2 analysis ports, each with in-situ degassing capability.
Simultaneously analyze different adsorbate gases across up to 2 stations.
Each port features an independent gas inlet (excluding Meso 112 model).
BET repeatability of ≤ ±1.0% ensures consistent, high-precision results.

Meso 400

High Throughput Mesopore Characterization

Designed for precise specific surface area and mesoporous structure characterization.
Balances high-throughput testing with independent station control.
Available with 4 analysis ports, each with in-situ degassing capability.
Simultaneously analyze different adsorbate gases across up to 4 stations.
Each port features an independent gas inlet.
BET repeatability of ≤ ±1.0% ensures consistent, high-precision results.

Micro 100

High-Resolution Micropore Characterization

Available in multiple models to support diverse lab-throughput needs.
2 analysis stations with high-vacuum pump and up to 3 pressure transducers per station.
Capable of measuring adsorption isotherms down to P/P₀ = 10⁻⁸ for high-resolution micropore characterization.
Simultaneous testing with different adsorbate gases across all active stations.
Integrated design supports up to 2 degassing ports, 2 in-situ, and 1 cold trap within a single cabinet.
BET repeatability of ≤ ±1.0% ensures consistent, high-precision results.

Micro 200

High-Resolution Micropore Characterization

Available in multiple models to support diverse lab-throughput needs.
2 analysis stations with high-vacuum pump and up to 3 pressure sensors per station.
Capable of measuring adsorption isotherms down to P/P₀ = 10⁻⁸ for high-resolution micropore characterization.
Simultaneous testing with different adsorbate gases across all active stations.
Integrated design supports up to 2 degassing ports, 2 in-situ, and 1 cold trap within a single cabinet.
Each analysis port includes a dedicated gas inlet (excluding Micro 100 model).
BET repeatability of ≤ ±1.0% ensures consistent, high-precision results.

Micro 300

High-Resolution Micropore Characterization

Available in multiple models to support diverse lab-throughput needs.
3 analysis stations with high-vacuum pump and up to 3 pressure sensors per station.
Capable of measuring adsorption isotherms down to P/P₀ = 10⁻⁸ for high-resolution micropore characterization.
Simultaneous testing with different adsorbate gases across all active stations.
Equipped with 3 in-situ degassing ports and 1 cold trap.
Each analysis port includes a dedicated gas inlet (excluding Micro 100 model).
BET repeatability of ≤ ±1.0% ensures consistent, high-precision results.

Vapor Series

Volumetric Vapor Adsorption Analyzer

Simultaneously perform vapor adsorption, specific surface area, and pore size distribution measurements.
Independent high-vacuum analysis pathways for vapor, BET surface area, and micropore characterization.
Analyze up to 2 samples at once (1 vapor, 1 micropore) with fully independent stations.
Configurable with 1 or 2 analysis stations to meet varying lab needs.
Includes cold trap, integrated constant-temperature valve box, and illuminated valve status indicators.

Surface DX Series

Cost-Effective Surface Area Analysis for Fast, Reliable Quality Control

Supports Dynamic Flow BET in three modes: patented dynamic reference method, single-point BET, and multi-point BET.
When fully optimized, up to 8 samples can be analyzed per hour across 4 stations.
High-sensitivity thermal conductivity detector with auto-zero for stable, accurate results.
Automatic Dewar elevator and valve status indicator lights streamline operation.
Compact, user-friendly design ideal for routine QC environments.
Widely adopted in carbon materials, battery components, ceramics, metal powders, and other industrial applications.